1. Why does the mold silica gel have fewer times of mold turning?
Too much silicone oil is added in the process of making the mold, and the silicone oil destroys the molecular weight of the silicone, so the mold will be turned over less times and not durable. If you do small products with more complex patterns, with high hardness of silica gel to open the mold, there will be fewer times to turn the mold phenomenon, because the silica gel is very brittle and easy to break. On the contrary, if you build products and use silica gel with small hardness to make molds, the results will also be unsatisfactory. Because the silicone is too soft, its tensile and tearing strength will be reduced, resulting in deformation of the mold, so the number of mold turns will be reduced. Mold glue itself is of good quality, there is no good or bad silicone, only suitable and not suitable. We should use silicone suitable for the hardness of the product to make the mold, there will be no such situation.

2. Why does the silica gel of the mold burn the mold?
Because unsaturated resin and resin products with peroxide curing agent, resin reaction will produce a lot of heat, the general curing time of resin is 3 minutes, so after 3 minutes to release as soon as possible, to prevent the silica gel mold will not produce the phenomenon of burning.

3. The production method of mould silicone filling mold and fragmentation mold:
Section mold or die operation method: the vacuum silica gel to brush or perfusion method for construction. If you are making a die or a piece die with a brush, brush the product or model you want to copy with a layer of release agent or isolator before brushing, and then brush the silicone on the product (note: Be sure to brush evenly) wait for 30 minutes, the surface paste a layer of gauze or glass fiber cloth to increase the strength, and then coated with a second layer of silicone, such as silicone dry, and then do the outer mold, the outer mold can use gypsum or resin and other materials.

Perfusion mold or perfusion mold operation method: perfusion mold or perfusion mold, is used for relatively smooth or simple products, that is, the product or model you want to copy, surrounded by rubber plate or glass plate, the vacuum of silicone directly poured into the product, after the silicone dry molding, take out the product, the mold is formed (Note: Perfusion mold generally uses soft silicone to do mold, so that demudding is easier, will not damage the products in the silicone mold), the above is the whole process of the use and operation of the silicone mold.

4. Why can mold silica gel surface dry phenomenon?
Mold silica gel is a condensation type silica gel, it is by absorbing water in the air and curing, silicone in the process of making, the water evaporation, but not transferred into the right amount of water, there will be this phenomenon. Solution: this phenomenon does not belong to the product quality problem, but because there is no control of water, improve the storage period of silica gel, shelf life for a long time will appear some phenomenon, as long as the use of silica gel, add 0.05% water, stirring evenly can solve some of the situation.

5 Why will the silicone of the mold appear the phenomenon of tension difference?
Because in the process of making the mold, in order to reduce the viscosity of silica gel, so that silica gel is easy to operate and a large number of silicone oil is added in silica gel, this will make silica gel become very soft, produce tensile resistance, tear strength reduction, tension deterioration phenomenon, resulting in the mold is not durable, short service life, less times of turning mold phenomenon.

6. Why does the mold appear oil?
Mold silicone itself is not oil, oil is because in the process of operation added compound silicone oil (silicone oil and white mineral oil complex ligand), because white mineral oil is a petrochemical product, not silicon oil.

7. Why does the mold have acid and alkali resistance and aging resistance?
In the process of making silicone molds, we suggest that customers had better not add any silicone oil. If necessary, the amount of silicone oil added should not exceed 5% ~ 10% at most. Because the addition of too much silicone oil will destroy the molecular weight of silicone, so the mold made will produce acid and alkali resistance, aging resistance phenomenon.

8. Why will the surface of the mold made of silicone have traces, stripes, non-smooth and other phenomena?
This occurs when the product or model to be copied has not been polished or polished. In fact, the model or product itself is not smooth or perfect, so if the product or model to be copied is not polished or polished, the mold made of good silicone will not be beautiful and smooth enough. There is also a situation that when playing release agent, no uniform brushing will also cause the mold is not smooth.